Eshop roka 2025 s vykurovacou technikou

Flange kontraventil - serie 06 - uden fjeder - DN 300; L=38mm BRA.06.430

Kode: I06430300
Ikke bedømt Detaljer om bedømmelse
1 469,85 € –20 %
Vykurovacia technika Medziprírubová spätná klapka - séria 06 - bez pružiny - DN 300; L=38mm
1 469,85 € –20 % 1 175,88 € / stk. 956 € ekskl. moms Mål pris:
International levering
Skaffevare (1-2 uger)

Detaljerede oplysninger

Detaljeret beskrivelse af produktet

Mellemflange kontraventil - vandret, BRA.06.430, størrelse: DN 300, længde: 38 mm, uden fjeder

 

  • maks. tryk 12 bar 
  • montering mellem flanger PN6 (kun op til DN 250)/PN10/PN16 iht. STN EN 1092-1
  • T = -20 °C til maks. +100 °C
  • til opvarmning og aircondition (HVAC), vandforsyning, trykluft, olier og kulbrinter
  • materiale - hus, skive: kulstofstål A216 WCB, fjeder: AISI 302, pakning: NBR
  • minimum modtryk for lukning 0,3 bar
  • anvendelse til vand med et indhold på op til 50 % glykoler
  • ikke egnet til damp

Ofte stillede spørgsmål

  • Hvordan vælger jeg den rigtige type og størrelse af fittings/ventiler? Følg det nominelle tryk (PN) og driftstemperaturen (T) angivet i de tekniske specifikationer - de skal svare til eller overstige de faktiske driftsforhold i dit system, og tilslutningsstørrelsen skal svare til rørdiameteren.
  • Hvordan fungerer denne fitting/ventil? Det præcise funktionsprincip (lukning, trykregulering, tilbageflow osv.) afhænger af den specifikke type - en detaljeret beskrivelse af funktionen findes ovenfor ved dette produkt.
  • Skal monteringen udføres af en professionel? Enkle afspærringsventiler kan monteres af en gør-det-selv-mand, men ved regulerings- og sikkerhedsventiler (sikkerhedsventiler, trykreducerende ventiler) anbefaler vi altid en professionel, da det drejer sig om elementer med en sikkerhedsfunktion.

Yderligere parametre

Kategori: BRA.06.430, BRA.M6.430 PR - kontraventiler - vandret
Garanti: 2 år
Vægt: 5 kg
Materiale: karoseri
Nominel diameter (DN): DN 250 eller mere
Armaturtype: kontraklap / ventil
Nominelt tryk: PN 6
Nominel vidde: DN 300
Seneste prisopdatering: 13.04.2026 1:09:25

Produktvurdering

Vær den første, der skriver en artikel til dette emne!

Udfyld ikke dette felt

Hvordan vil du bedømme dette produkt? Vælg mellem 1 og 5 stjerner, hvor 1 er den dårligste og 5 den bedste bedømmelse.

Diskussion

Udfyld ikke dette felt

Liste over diskussioner

J Avatar af forfatter 19.10.2026 20:18
We're swapping out an old valve for this DN 300 one, but our pipes are flanged PN16. Is that okay since the specs say it only works up to PN10 for sizes over DN250?
A Avatar af forfatter 19.10.2026 20:18
Actually, you need to be careful here because the product sheet states this specific model is only approved up to PN10 when installed on sizes larger than DN250. Since your system is PN16 and this unit is DN300, it won't meet the required pressure rating for safety. You might want to check our other horizontal check valves that support higher pressures for this pipe size.

IVAR designs, develops and manufactures highly energy-efficient heating and plumbing systems. We have over 10,000 catalogue items - mass-produced products and unique items - in addition to customised systems and combinations of complex products. And it’s all “Made in Italy”.

 

Vision
To make life easier for our clients, our clients' customers and our employees, thanks to our ability to be constantly innovative.

 

Mission
To design and manufacture advanced hydronic solutions that reduce installation complexity and energy consumption.

 

“Made in Italy” adds value

IVAR has been producing heating and plumbing system components since 1985: valves for heating bodies, direct heat metering modules, heat cost allocators, pipes and fittings, substations for heating systems, distribution manifolds, radiant panel systems, and components for solar and geothermal systems. And it’s all “Made in Italy”.
Over 200 people are employed at our manufacturing facilities in Prevalle (in northern Italy’s Brescia province). The site has been designed to streamline our many production and operational stages.

The Italian headquarters also acts as a hub for the wider IVAR Group, set up with the goal of distributing products beyond Italy’s borders. The group now has 11 branches, in Australia, Belgium, China, Germany, the United Kingdom, the Czech Republic, Romania, Slovakia, Spain, the United States and Tunisia.

 

Know How
Research, development and numerous laboratory tests guarantee that our clients’ requests can be translated into new high-efficiency products.

The stages required for production take place internally, beginning with hot forming, which is carried out at our subsidiary Valmon Stampati. Our continuous implementation of projects under the Industry 4.0 initiative also allows us to take full advantage of new releases in technology and IT to improve our manufacturing efficiency.


As a company, IVAR is constantly evolving. Every day, we invest in strengthening our products, in improving our production processes and in attaining new patents and certifications.

Vytvořil Shoptet | Design Shoptak.cz.